Changeset 1787 for CONFIG/UNIFORM/v5/LMDZREPR_v5
- Timestamp:
- 06/25/12 19:08:33 (12 years ago)
- File:
-
- 1 edited
Legend:
- Unmodified
- Added
- Removed
-
CONFIG/UNIFORM/v5/LMDZREPR_v5/EXPERIMENTS/LMDZREPR/ref1/COMP/lmdz.card
r1750 r1787 9 9 # NPv3.1 for new physics, to be used with LMDZ5/trunk revision 1554 or later 10 10 LMDZ_Physics=AP 11 #LMDZ_Physics=NPv3.1 12 13 # You can choose here the name of create_etat0 you want to use 14 # If noting is defined here, the job will get the JobName in the file ../CREATE/config.card 11 12 # Set the variable CREATE needed further below to find the initial and boundary condition files. 15 13 CREATE=ELI-${RESOL_ATM_3D} 14 15 # ByPass_hgardfou_teta=y : modify teta_ parameters for following CumulPeriod only 16 16 ByPass_hgardfou_teta=n 17 18 # ByPass_hgardfou_mats=y : set parameter purmats=y for following CumulPeriod only 17 19 ByPass_hgardfou_mats=n 20 21 # Number of periods where to set parameter adjust=y before switching to adjust=n 22 # For adjust=n, set LMDZ_NbPeriod_ajust=0. 18 23 LMDZ_NbPeriod_adjust=3 19 # LMDZ_NbPeriod_adjust=0 20 # To force usage of this Bands file, put LMDZ_NbPeriod_adjust=0 and replace XXXXXXX by Restart Job Name24 25 # To force usage of specific Bands file, set LMDZ_NbPeriod_adjust=0 and replace XXXXXXX by Restart Job Name 21 26 # LMDZ_Bands_file_name=${ARCHIVE}/IGCM_OUT/IPSLCM5/XXXXXXX/ATM/Debug/XXXXXXX_Bands_96x95x19_3prc.dat_3 27 28 # Set ConfType to choose parameters for aerosols, solar and green house gazes. 29 # The parameter file PARAM/config.def_$ConfType will be used. 30 # ConfType=preind/actuel/annuel 31 ConfType=annuel 32 33 # Set OutLevel to choose the level of output files from LMDZ. The file PARAM/output.def_$OutLevel will be used. 34 # OutLevel=low/medium/high 35 OutLevel=low 22 36 23 37 # Set COSP activation and Outputs frequency (monthly, daily, HF) = y/n … … 32 46 LMDZ_NMC_hf=n 33 47 34 # Other specific parameters to this experience35 aer_type=annuel36 pmagic=0.037 38 48 # Nugding : ok_guide=y/n 49 # If ok_guide=y, add nudging files(u.nc, v.nc, hur.nc,...) in BoundaryFiles section below. 39 50 ok_guide=n 40 51 … … 61 72 (${SUBMIT_DIR}/PARAM/cosp_input_nl.txt, .), \ 62 73 (${SUBMIT_DIR}/PARAM/cosp_output_nl.txt, .), \ 74 (${SUBMIT_DIR}/PARAM/output.def_${OutLevel}, output.def), \ 75 (${SUBMIT_DIR}/PARAM/config.def_${ConfType}, config.def), \ 63 76 (${SUBMIT_DIR}/PARAM/guide.def, .), \ 64 77 (${SUBMIT_DIR}/PARAM/run.def, .), \ … … 70 83 71 84 [OutputText] 72 List= (physiq.def, gcm.def, run.def, traceur.def, guide.def, used_run.def)85 List= (physiq.def, gcm.def, run.def, traceur.def, guide.def, config.def, output.def, used_run.def) 73 86 74 87 [OutputFiles]
Note: See TracChangeset
for help on using the changeset viewer.